Recent technologyIndia

Food Packaging Materials for Shelf Life in India: Oxygen and Moisture Barriers by Product Type

The best food packaging materials for shelf life in India are the simplest structures whose oxygen and water vapour transmission rates (OTR and WVTR) stay below what the product can tolerate at Indian storage temperature and humidity. EVOH, PVDC, oxide-coated, metallised and foil layers give the lowest rates, but the limit is set by the formula, and the pack must also meet FSSAI food-contact and plastic-waste EPR rules.
SIDr Shreya Iyer
PhD (Food Science) · Director of New Product Development, Food Research Lab
✓ Technically reviewed by the Formulation & Regulatory Panel · Last reviewed: 28 October 2026 · Next review: June 2027
Posted
28 October 2026

Last checked
28 October 2026

Reading time
12 min

Sources
14
At a glance
  • A barrier is a number at a stated test condition: OTR and WVTR both change with temperature and humidity, so datasheet values can understate ingress in an Indian summer.
  • Oxygen permeability spans four orders of magnitude, from 3,100 for LDPE to 0.5–7.1 for EVOH and 0.1–0.3 for PVDC.
  • Coatings on cast PP cut OTR from 1,516 to about 0.04 cm³/m²·day·bar in a 2024 study.
  • Work backwards from the product: a 0.05 m² pack that tolerates 2 cm³ of oxygen over 180 days needs ingress of no more than 0.22 cm³/m²·day.
  • FSSAI: plastics must pass 60 mg/kg or 10 mg/dm² overall migration, with an NABL conformity certificate for food-contact layers.
  • EPR: all-plastic laminates are Category II; plastic with foil or paper is Category III.
Key numbers
Uncoated cast PP (CPP70) OTR
1,516 cm³/m²·day·bar
Michem Flex B3513 coat on CPP70
About 2.75 (551-fold lower)
Michem Flex + PVOH double coat
About 0.04 (about 38,000-fold lower)
Coated PP/SiOx and OPP/AlOx
Below 0.1 cm³/m²·day·bar
FSSAI overall migration limit (plastics)
60 mg/kg or 10 mg/dm²
Oxygen in air (for in-air ingress)
About 21% (0.21 bar)

Introduction

Food product packaging that performs well in a temperate laboratory can fail in an Indian summer, because the transfer of oxygen and water vapour through a film depends on temperature and relative humidity.[1] A pack’s barrier is therefore a measured number at a stated test condition, not a label on a datasheet.

This article explains what high-barrier packaging is, how the layers work, which food packaging materials suit which products, how to turn a shelf-life target into a required transmission rate, and which Indian food-contact and plastic-waste rules apply. For a general comparison of barrier data across materials, see our earlier post on barrier property benchmarking in India.

What High-Barrier Packaging Technology Is

A pack slows four transfers: oxygen in, which drives oxidation and rancidity; moisture in or out, which softens crisp foods or dries soft ones; light, which degrades sensitive compounds; and aroma loss.[2] Oxygen transfer is rated by the oxygen transmission rate (OTR) and moisture transfer by the water vapour transmission rate (WVTR). Lower values mean a better barrier, and both depend on temperature and relative humidity.[1]

Food packaging materials reach low rates by layering. A typical flexible structure has a strong, printable outer film (PET or BOPP), a thin barrier layer (EVOH, an oxide coating, metallisation or foil) and a heat-sealable inner layer (PE or PP).

Schematic of a multilayer barrier film: oxygen and water vapour from hot, humid outside air are stopped by an outer PET or BOPP film, an EVOH, oxide, metal or foil barrier layer and a PE or PP sealant, with a pathway through a defect into a biscuit pack
Figure 1. How a multilayer barrier film works: the barrier layer stops most oxygen and water vapour; pinholes, flex-cracks and weak seals let more through (FRL schematic, not to scale).

How the Barrier Works

Permeation through the film

Gas crosses a polymer by dissolving into one face, diffusing through the film and leaving from the other face. Transfer therefore rises with the material’s permeability and the pack area and falls as the barrier gets thicker. Oxygen permeability coefficients span four orders of magnitude: 3,100 for LDPE, 1,790 for PP, 35.9 for PET, 0.5 to 7.1 for EVOH and 0.1 to 0.3 for PVDC (×10−20 kg·m/(m²·s·Pa)).[1]

A thin coating can cut the rate dramatically. In a 2024 study on cast polypropylene film (CPP70), the uncoated film had an OTR of 1,516 cm³/m²·day·bar. Single coatings of ORMOCER® and Michem® Flex B3513 reduced it by factors of 88 and 551, and coated SiOx- and AlOx-PP films reached OTR values below 0.1 cm³/m²·day·bar.[3]

Real packs usually perform worse than flat-film data suggest, because pinholes, flex-cracks and weak seals bypass the barrier (FRL view). EVOH also loses barrier as humidity rises,[3] so its value depends on where it sits in the structure and on storage conditions.

How OTR and WVTR are measured

OTR of plastic film and sheeting is commonly measured with a coulometric oxygen sensor under ASTM D3985.[4] ASTM F1927 runs the same type of measurement at a controlled relative humidity,[5] which matters for humidity-sensitive barriers such as EVOH. WVTR is measured with a modulated infrared sensor under ASTM F1249[6] or gravimetrically, with desiccant or water cups, under ASTM E96/E96M.[7]

ASTM E96 notes that a WVTR obtained under one set of test conditions cannot be used to predict the result under different conditions.[7] A datasheet value is only comparable with another if the method, temperature and humidity match. Ask suppliers for OTR and WVTR at a condition close to your storage climate, then confirm the result in a real-time or accelerated shelf-life study of the packed product.[2]

Key Components and Methods

Oxygen barriers: EVOH, PVDC, metallised film and foil

EVOH, PVDC, metallised films, oxide-coated films and aluminium foil laminates are the usual oxygen barriers in high-barrier packaging. EVOH has an oxygen permeability of 0.5 to 7.1 and PVDC 0.1 to 0.3 (×10−20 kg·m/(m²·s·Pa)).[1] EVOH is normally buried as a thin inner layer between polyolefins, because its oxygen barrier falls as it takes up moisture.[3] Its water vapour permeability (320 to 560) is far higher than that of HDPE (2.1) (×10−16 kg·m/(m²·s·Pa)).[1]

Moisture barriers

A moisture barrier film is chosen on WVTR. For crisp biscuits and powders, the aim is to keep moisture out; for soft foods, to keep it in. Polyethylene layers carry much of this role: HDPE and LDPE list water vapour permeabilities of 2.1 and 5.5, and PVDC 1.2 to 7.3, against 161 for PLA and 320 to 560 for EVOH (×10−16 kg·m/(m²·s·Pa)).[1] Metallised, oxide-coated and foil layers add further water vapour barrier, and opaque layers also block light (FRL view).

Active and modified atmosphere packaging

Active packaging adds functional components such as oxygen scavengers, moisture absorbers, antimicrobial agents and ethylene or odour absorbers.[8] Modified atmosphere packaging (MAP) replaces the air in the pack, often with nitrogen, and works only if the film and seals hold the gas. Both support a sound passive barrier; neither replaces it (FRL view). For chilled foods, removing oxygen by vacuum packing or MAP can favour anaerobic bacteria, including Clostridium botulinum, so these packs need a specific safety assessment.[2]

Table 1. Barrier components and their functions

Component Main function Evidence and watch-outs
Polyolefin sealant (LDPE, HDPE, PP) Heat seal; water vapour barrier Oxygen permeability 424 (HDPE) to 3,100 (LDPE); water vapour 2.1 (HDPE) and 5.5 (LDPE)[1]
PET outer film Strength and print surface; lower oxygen permeability than polyolefins Oxygen 35.9; water vapour 7.8[1]
EVOH layer Oxygen barrier Oxygen 0.5 to 7.1; water vapour 320 to 560;[1] barrier falls as humidity rises[3]
PVDC Oxygen and moisture barrier Oxygen 0.1 to 0.3; water vapour 1.2 to 7.3[1]
Oxide (SiOx, AlOx) or barrier coating on PP Oxygen barrier on a recyclable-oriented base film Coated PP/SiOx and OPP/AlOx below 0.1 cm³/m²·day·bar OTR;[3] thin layers are vulnerable to flex-cracking (FRL view)
Oxygen scavenger or MAP Removes or displaces residual oxygen Needs a sealed, low-leak pack;[8] vacuum and MAP chilled foods need a botulism risk assessment[2]

Permeability coefficients are from Table 1 of a 2022 review, which does not state the test temperature or humidity for each value.[1] Units: oxygen ×10−20 kg·m/(m²·s·Pa); water vapour ×10−16 kg·m/(m²·s·Pa). Compare within a column, not across columns.

Food, Beverage and Nutraceutical Applications

Dry, moisture-sensitive products

Biscuits, extruded snacks, instant beverage mixes and nutraceutical powders lose crispness or flow when they gain moisture, so the priority is a low WVTR. Polyethylene and PVDC list the lowest water vapour permeabilities in the review,[1] and metallised or foil layers add barrier. Pair a moisture barrier film built on these layers with a tight seal.

Oily, oxygen-sensitive products

Nuts, fried snacks and fat-rich foods oxidise, so the priority is a low OTR: oxygen barrier packaging built on EVOH or PVDC, with oxygen permeabilities of 0.5 to 7.1 and 0.1 to 0.3,[1] or on a metallised, oxide-coated or foil layer. Nitrogen flushing reduces the oxygen already in the pack, but only a low-OTR film and good seals keep it low.

High-moisture and chilled products

Sauces, ready meals and chilled desserts usually need an oxygen barrier and, for retorted packs, heat resistance. Because EVOH’s barrier is humidity-sensitive,[3] structures for wet or heat-processed products should be tested after the actual fill, seal and heat process, not only as flat film (FRL view). Vacuum and MAP chilled products also need a risk assessment for anaerobic pathogens.[2]

Five-step workflow: name the failure, fix the limit from the shelf-life study, convert it to a maximum OTR or WVTR, compare films at your temperature and humidity, and confirm in pack with a shelf-life trial and seal and flex tests
Figure 2. From the product’s failure mode to a confirmed pack (FRL framework). Steps 3 and 4 are worked through in the next section.

Benefits and Performance Considerations

The benefit of a barrier is a measurable shelf-life margin, and the required barrier can be calculated. Worked example with assumed values: a pack with 0.05 m² of film area, holding a product that tolerates 2 cm³ of oxygen ingress over a 180-day shelf life, needs an in-air ingress rate of no more than 2 ÷ (0.05 × 180) = 0.22 cm³/m²·day.

Film OTR is reported per bar of oxygen partial-pressure difference. Air contains about 21% oxygen, so if the pack interior holds almost no oxygen, the ingress rate in air is roughly the OTR multiplied by 0.21. Table 2 applies this to the cast PP results from the 2024 coating study.

Table 2. Coated and uncoated PP films against a 0.22 cm³/m²·day limit (assumed pack)

Film OTR (cm³/m²·day·bar) In-air ingress (× 0.21) Against the limit
Uncoated cast PP (CPP70)[3] 1,516 318 About 1,400 times over
CPP70 + ORMOCER® (88-fold reduction)[3] About 17 3.6 About 16 times over
CPP70 + Michem® Flex B3513 (551-fold)[3] About 2.75 0.58 About 2.6 times over
CPP70 + ORMOCER® + PVOH (about 20,000-fold)[3] About 0.08 0.016 Within, about 7% of the limit
CPP70 + Michem® Flex + PVOH (about 38,000-fold)[3] About 0.04 0.008 Within, about 4% of the limit
Coated PP/SiOx or OPP/AlOx[3] Below 0.1 Below 0.021 Within, under 10% of the limit

OTR values are calculated from the uncoated value and the reduction factors reported for cast PP.[3] They are laboratory flat-film results, not values at Indian storage temperature and humidity, so read Table 2 as a ranking, not a pass mark.

Formulator’s note: set the limit in the formula, not in the film. The film does not decide how much oxygen a product can tolerate; the formula does. In the worked example, a formula that tolerates twice as much oxygen doubles the allowable rate and widens the choice of film. Agree the failure limit during food product formulation, before the film is chosen. The best packaging for food shelf life is then the simplest structure that meets the rate with margin at your storage condition: in Table 2, a single Michem Flex coat on cast PP misses the limit by about 2.6 times, while a double coating or a coated SiOx or AlOx film meets it with a wide margin.

Limitations, Challenges and Indian Regulations

FSSAI food-contact requirements

Under the Food Safety and Standards (Packaging) Regulations, 2018, any material in contact with food must be food grade and suitable for the product, its storage conditions and its filling, sealing and transport. In a multilayer pack, the layer in direct contact with food, or likely to come into contact with it, must meet the materials specified in Schedules I to III. The food business operator must hold a certificate of conformity from an NABL-accredited laboratory for those layers.[9]

All plastic packaging materials must pass the overall migration limit of 60 mg/kg or 10 mg/dm² when tested to IS 9845, with no visible colour migration. Printing inks must conform to IS 15495, and the printed surface must not touch the food. Aluminium foil laminates are listed under IS 8970 and bare aluminium foil for food packaging under IS 15392. Schedule III lists the plastics, including polyethylene (IS 10146), polypropylene (IS 10910) and PET (IS 12252).[9] EVOH is not named in Schedule III, so in practice it sits behind a listed food-contact layer; confirm the specification with your testing laboratory (FRL reading).

The FSSAI compendium cited here is Version III of 1 June 2022.[9] Two amendments have followed: an August 2022 amendment added specific migration limits for antimony (0.04 mg/kg) and DEHP (1.5 mg/kg),[10][11] and the First Amendment Regulations of 28 March 2025 allow recycled PET for food packaging once FSSAI notifies standards and guidelines.[11] For how food type and temperature set migration test conditions, see our guide to migration test conditions.

Plastic Waste Management Rules and EPR

Extended producer responsibility (EPR) under the Plastic Waste Management (PWM) Rules applies once the pack contains plastic. Producers, importers and brand owners register on the CPCB portal and carry targets by category: rigid plastic (I); flexible plastic packaging of a single layer or multilayer of different plastics (II); multilayered packaging with at least one plastic layer and at least one non-plastic layer (III); and compostable plastic sheets (IV).[12]

An all-plastic barrier laminate such as PET/EVOH/PE therefore falls in Category II, and a PET/foil/PE or paper-based laminate in Category III (FRL reading of the definitions; confirm metallised structures with your EPR adviser). From 1 July 2025, producers, importers and brand owners must give the information specified in the rules through a barcode or QR code, a product information brochure or a unique number printed on the plastic packaging, and contraventions are dealt with under section 15 of the Environment (Protection) Act, 1986.[13] A further amendment notified on 31 March 2026 (G.S.R. 237(E)) is reported to revise recycled-content and reuse obligations, with Category III targets applying to the plastic component only.[14] Check the current text before you finalise a structure.

The climate gap

The barrier values in this article are laboratory values, not values at Indian storage temperature and humidity. Until the chosen structure has been tested at your distribution condition and on the packed product, the climate gap remains open.

Outlook and Development Direction

Recent literature points in three directions. Oxide and polymer coatings can give a polypropylene base film a high oxygen barrier, which is attractive because multilayer flexible packaging made from mixed materials is hard to recycle.[3] Researchers are also tailoring the barrier properties of bio-based PLA[1] and broadening active-packaging systems.[8]

Paper-based packs are following a similar path, as grease barriers move away from fluorinated chemistry: see PFAS-free paper packaging rules in the GCC and the research on fat migration in PFAS-free paper. Whether a new structure is recyclable in practice depends on its EPR category and on local recyclers (FRL view).

Conclusion

Choosing food packaging materials for shelf life means matching a product’s failure mode to a film’s measured OTR and WVTR at the temperature and humidity of your supply chain. Set the oxygen or moisture limit in the formula, compare films measured by the same method at a relevant condition, check the structure against FSSAI and EPR rules, and confirm it in a shelf-life study on the packed product.

For Brands & Formulators

If you are launching or re-packing a product for Indian distribution, FRL can help you match the pack to the product rather than to a datasheet.

  • Define the limit: the product’s failure mode (oxidation, moisture gain or loss, light, aroma) and how much oxygen or moisture it can tolerate.
  • Shortlist structures: convert the limit to a required OTR and WVTR and compare candidate films measured at a relevant condition.
  • Confirm in pack: run the shelf-life trial on the packed product, with seal and flex checks, and confirm FSSAI conformity for food-contact layers.

Start with FRL’s packaging barrier and compatibility testing, pair it with a shelf-life study of the finished product, or contact the team to scope the work.

What to do now
  • ✓Name the failure mode for each SKU: oxidation, moisture gain or loss, light or aroma.
  • ✓Set the limit in the formula and convert it to a required OTR and WVTR for your pack size and shelf life.
  • ✓Ask suppliers for the full test basis: method (ASTM D3985/F1927, F1249/E96), temperature and humidity behind every OTR and WVTR.
  • ✓Check compliance: FSSAI Schedule I–III standards and an NABL certificate for food-contact layers, and the EPR category of the structure.
  • ✓Confirm in pack with a shelf-life study at your distribution condition.
Your next step
Match your pack to your product
1Share your product, target shelf life and distribution climate.
2FRL converts the product’s limit into a required OTR and WVTR and shortlists barrier structures.
3Confirm the chosen pack in a shelf-life trial with seal and flex checks.
Questions brands ask
Which food packaging materials extend shelf life best?

Structures with an EVOH, PVDC, oxide-coated, metallised or foil layer give the lowest oxygen transfer; EVOH and PVDC have oxygen permeabilities of 0.5 to 7.1 and 0.1 to 0.3 against 3,100 for LDPE.[1] The best choice depends on the product’s main sensitivity: oxygen-sensitive foods need a low OTR, moisture-sensitive foods a low WVTR, and the structure should be no more complex than the limit requires.

What is the difference between oxygen and moisture barrier packaging?

Oxygen barrier packaging limits oxygen ingress to slow oxidation and protect flavour and colour, and is rated by OTR (for example ASTM D3985 or F1927).[4][5] A moisture barrier limits water vapour transfer to prevent sogginess or drying, and is rated by WVTR (ASTM F1249 or E96).[6][7] Many foods need both.

How do you choose packaging for a product in India’s climate?

Work out the oxygen or moisture limit from the product, convert it to a required OTR and WVTR, and compare films measured at a temperature and humidity close to your storage condition, since both affect permeation.[1] Then confirm the choice in a shelf-life study on the packed product.

What packaging regulations apply to food in India?

Food-contact safety is governed by the FSS (Packaging) Regulations, 2018, as amended: food-grade materials, Schedule I to III standards for food-contact layers, an overall migration limit of 60 mg/kg or 10 mg/dm² for plastics and an NABL conformity certificate.[9][11] Plastic packs also fall under the Plastic Waste Management Rules and EPR, which have been amended several times since 2022.[12][13][14]

Are datasheet OTR values enough to set shelf life?

No. Datasheet values are flat-film results at one test condition, and a WVTR at one condition cannot predict the result at another.[7] Pinholes, flex-cracks and seals also add leakage, so the finished pack must be tested with the product.

References
  1. Marano, S., Laudadio, E., Minnelli, C., & Stipa, P. (2022). Tailoring the barrier properties of PLA: A state-of-the-art review for food packaging applications. Polymers, 14(8), 1626. https://doi.org/10.3390/polym14081626 (Cited for: oxygen and water vapour permeability coefficients in Table 1; dependence of permeation on temperature and relative humidity.)
  2. Food Standards Scotland. (2025). Shelf-life guidance: Guidance for food businesses for the setting of product shelf-life (Version 1.2). https://www.foodstandards.gov.scot/sites/default/files/migration/downloads/Shelf-life_guidance_2025.pdf (Cited for: packaging barrier, light and atmosphere as shelf-life factors; anaerobic and C. botulinum risk in vacuum and MAP packs.)
  3. Sharbafian, F., Tosic, K., Schmiedt, R., Novak, M., Krainz, M., Rainer, B., & Apprich, S. (2024). Investigation and comparison of alternative oxygen barrier coatings for flexible PP films as food packaging material. Coatings, 14(9), 1086. https://doi.org/10.3390/coatings14091086 (Cited for: OTR of uncoated cast PP and the reduction factors for coated films; coated SiOx/AlOx-PP below 0.1 cm³/m²·day·bar; EVOH humidity sensitivity; recyclability of multilayer packaging.)
  4. ASTM International. (2024). Standard test method for oxygen gas transmission rate through plastic film and sheeting using a coulometric sensor (ASTM D3985-24). https://store.astm.org/standards/d3985 (Cited for: OTR test method.)
  5. ASTM International. (2020). Standard test method for determination of oxygen gas transmission rate, permeability and permeance at controlled relative humidity through barrier materials using a coulometric detector (ASTM F1927-20). https://store.astm.org/standards/f1927 (Cited for: OTR at controlled relative humidity.)
  6. ASTM International. (2020). Standard test method for water vapor transmission rate through plastic film and sheeting using a modulated infrared sensor (ASTM F1249-20). https://store.astm.org/f1249-20.html (Cited for: instrumental WVTR test method.)
  7. ASTM International. (2024). Standard test methods for gravimetric determination of water vapor transmission rate of materials (ASTM E96/E96M-24a). https://store.astm.org/e0096_e0096m-24a.html (Cited for: gravimetric WVTR method; results at one condition do not predict results at another.)
  8. Kadirvel, V., Palanisamy, Y., & Ganesan, N. D. (2025). Active packaging system: An overview of recent advances for enhanced food quality and safety. Packaging Technology and Science, 38(2), 145–162. https://doi.org/10.1002/pts.2863 (Cited for: active packaging components, including oxygen scavengers and moisture absorbers.)
  9. Food Safety and Standards Authority of India. (2022). Food Safety and Standards (Packaging) Regulations, 2018: Compendium (Version III, 1 June 2022). https://www.fssai.gov.in/upload/uploadfiles/files/Compendium_Packaging_Regulations_05_06_2022.pdf (Cited for: regulations 3 and 4, multilayer and NABL requirements, overall migration limit, Schedules I–III.)
  10. SGS. (2022, October). India strengthens chemical safety in food contact plastics (SafeGuardS 115/22). https://www.sgs.com/en/news/2022/10/safeguards-11522-india-strengthens-chemical-safety-in-food-contact-plastics (Cited for: secondary summary of the August 2022 amendment adding antimony and DEHP specific migration limits.)
  11. Food Safety and Standards Authority of India. (2025, March 28). Food Safety and Standards (Packaging) First Amendment Regulations, 2025 (F. No. STD/SP-20/T(Recycledplastics-N)). The Gazette of India: Extraordinary, Part III, Section 4. https://www.fssai.gov.in/upload/uploadfiles/files/FSS_Packaging_Amendment%20Regulations2025%20related%20to%20recycled%20plastics.pdf (Cited for: recycled PET provision; list of amendments of 25 January 2022 and 30 August 2022.)
  12. Ministry of Environment, Forest and Climate Change. (2022, February). Plastic Waste Management (Amendment) Rules, 2022: Guidelines on extended producer responsibility for plastic packaging [Gazette notification]. https://tnpcb.gov.in/owems/pdf/regulations/4th%20Amendment%20(EPR%20guidelines)%20Feb%202022.pdf (Cited for: EPR registration and plastic packaging categories I–IV.)
  13. Ministry of Environment, Forest and Climate Change. (2025, January 23). Plastic Waste Management (Amendment) Rules, 2025. The Gazette of India: Extraordinary, Part II, Section 3(i). https://egazette.gov.in/WriteReadData/2025/260415.pdf (Cited for: information by barcode, QR code, brochure or unique number from 1 July 2025; action under section 15 of the Environment (Protection) Act, 1986.)
  14. Corporate Professionals. (2026, April 7). Plastic Waste Management (Amendment) Rules, 2026: Strengthening EPR, recycled content and reuse obligations. https://www.corporateprofessionals.com/regulatoryupdate/plastic-waste-management-amendment-rules-2026-strengthening-epr-recycled-content-and-reuse-obligations/ (Cited for: secondary summary of G.S.R. 237(E), 31 March 2026; Gazette text not verified.)