Case studyIndia

Dog Treat Pilot Batch: A Worked Example for Pet Food Start-Up Founders

A dog treat pilot batch is a small trial run that proves a recipe, process and pack before a full production run. This worked example follows a hypothetical start-up’s 50 kg baked-treat pilot from brief to scale-up decision: yield after baking, moisture and water-activity targets, shelf-life and safety testing, and cost per pack. Every input is assumed and every result is calculated; no client data is shown.
SIDr Shreya Iyer
PhD (Food Science) · Director of New Product Development, Food Research Lab
✓ Technically reviewed by FRL Editorial · Last reviewed: 17 November 2026 · Next review: May 2027
Posted
17 November 2026

Last checked
17 November 2026

Reading time
9 min

Sources
5
At a glance
  • Labelled worked example: Brand P (hypothetical), a two-founder start-up, plans a 50 kg baked dog treat pilot; every input is assumed.
  • Baking 50 kg of dough from 28% to 10% moisture gives 40 kg of treats, an 80% yield, or 400 packs of 100 g (calculated).
  • Cost per pack: ₹103.9 at pilot against ₹34.4 at a 500 kg minimum order, about two-thirds less (calculated).
  • The ₹41,550 pilot costs about 30% of a ₹1,37,500 run that fails at scale (calculated).
  • Finished moisture moves cost per pack only about 2% either side of target; set it from shelf-life and safety data.
Key numbers
Finished treats from 50 kg dough at 10% moisture (calculated)
40 kg (80% yield)
Packs of 100 g from the pilot (calculated)
400
Cost per pack: pilot vs 500 kg run (calculated)
₹103.9 vs ₹34.4
Pilot cost vs a failed 500 kg run (calculated)
₹41,550 vs ₹1,37,500
Measured results on this page
None (worked example)

About this worked example

This is a labelled worked example, not a client case study. Brand P is a hypothetical start-up, and every input on this page (batch size, moisture levels, ingredient, run-fee, testing and packaging costs, minimum order quantity) is an assumption. Yields and costs are calculations from those assumptions. No dogs were fed, no samples were tested and no shelf-life, palatability or cost result on this page is measured.

The page shows how Food Research Lab plans a dog treat pilot batch for pet food start-up founders: recipe, bake trial, shelf-life and safety testing, then cost per pack and the scale-up decision. For another labelled worked example, see our retort soup pilot trial.

The brief: founders with a dog treat idea

Brand P is run by two founders who want to launch a baked chicken-and-oat dog treat in a 100 g pack with a nine-month ambient shelf life. They will use a contract manufacturer rather than build a factory, and they need numbers before they commit to a first commercial run: how many packs a batch gives, what each pack costs, and what has to be proven first.

Table 1. Worked-example brief (all values assumed)

Item Assumption
Product Baked chicken-and-oat dog treat, sold as a treat (not a complete diet)
Pack 100 g, ambient, nine-month shelf-life target
Pilot batch 50 kg of dough at 28% moisture
Finished-product targets 10% moisture; water activity at or below 0.60
Ingredient cost ₹95 per kg of dough
Run fee ₹14,000 for the 50 kg pilot; ₹24,000 for a 500 kg run
Testing budget ₹18,000 per run (shelf life and safety)
Packaging ₹12 per pack
Co-manufacturer minimum order quantity 500 kg of dough

From recipe to a dog treat pilot batch

Recipe scale-up starts with a 50 kg batch of dough. At 28% moisture, that dough holds 36 kg of solids (50 × 0.72). The solids are what end up in the pack, so every yield and cost figure below follows from that number. Our worked example on scaling a recipe from kitchen to pilot plant shows the same logic for human food.

Formulation and ingredient choices

Chicken, oats and binders are specified by supplier and grade, and the finished treat is analysed rather than assumed to match the recipe on paper. A 2025 analysis of 18 commercial insect-based dog foods found that the measured values of 7 differed from those declared on the pack, and several missed recommended mineral levels[1]. Baking also changes nutrient content, which our guide to nutrient losses in pet food processing covers in detail.

Because this is a treat and not a complete diet, it is positioned as a treat. In the US, AAFCO guidance says products not intended as complete feeds are labelled as treats or supplements, or “for intermittent or supplemental feeding only”, and do not carry a nutritional adequacy statement[2]. For Indian label and registration requirements, see our guide to pet food regulations in India and our explainer on pet food categories under IS 11968:2019.

Claims are planned at the same stage. A 2025 systematic review found no evidence that approved additives and preservatives cause harm within AAFCO limits, and could not reach a firm conclusion on human-grade versus feed-grade ingredients[3]. Claims such as “no preservatives” or “human-grade” therefore need their own evidence before they go on the pack.

The processing trial

The pilot compares three bake profiles (time and temperature) against the assumed targets of 10% finished moisture and water activity at or below 0.60. Moisture drives yield; water activity drives microbial stability. The moisture that delivers the target water activity is specific to each recipe, so in a real project it is measured on the product rather than taken from a table.

Each profile is judged on moisture, water activity and texture (snap, hardness, breakage). Dog acceptance is checked in a palatability trial run or arranged through partner facilities; our animal food product development page describes the palatability and acceptance trials we run with third-party partners. The chosen profile is then fixed and validated as the process.

Baking from 28% to 10% moisture leaves 36 ÷ 0.90 = 40 kg of treats from 50 kg of dough, an 80% mass yield, or 400 packs of 100 g.

A different format needs a different route. A soft or semi-moist chew depends on humectants and other hurdles to hold water activity down at higher moisture, and a wet treat in a can or pouch is heat-processed in a sealed container; see our retort wet pet food development page.

Shelf-life and safety testing

Shelf-life testing stores packed treats at room temperature and at a raised temperature, then tracks moisture, water activity, texture, rancidity markers and microbiology over time. Accelerated data can support a provisional date, but a nine-month claim is confirmed with real-time storage; our guide to real-time and accelerated shelf-life testing explains how the two fit together. The pack’s moisture and oxygen barrier is part of the test, which our guide to packaging for dry pet food covers.

Safety testing includes pathogens. Salmonella in pet food is a recognised risk to pets and to the people who handle it[4], and dog treats have been recalled over it, as in the Elite Treats chicken chips recall in the US. Low water activity stops growth but not survival: pathogens can persist for months in low-water-activity foods and dry processing environments, so control rests on hygiene, zoning and preventing contamination after baking[5].

In this example the shelf-life and safety tests are budgeted at an assumed ₹18,000 per run. Testing is run or arranged through accredited partner laboratories.

Costing and scale-up readiness

Table 2 compares the cost of a 100 g pack from the 50 kg pilot with a 500 kg run, the co-manufacturer’s assumed minimum order quantity (MOQ). At 500 kg the same 80% yield gives 4,000 packs, so the run fee and the testing budget are spread over ten times as many packs.

Table 2. Cost per 100 g pack, ₹ (assumed inputs; calculated)

Item Pilot (50 kg dough, 400 packs) 500 kg run (4,000 packs)
Ingredients (₹95 per kg of dough) 11.9 11.9
Run fee (₹14,000 / ₹24,000) 35.0 6.0
Testing (₹18,000 per run) 45.0 4.5
Packaging 12.0 12.0
Total per pack 103.9 34.4
Total for the run ₹41,550 ₹1,37,500

At the MOQ, cost per pack falls by about two-thirds (from ₹103.9 to ₹34.4). Testing is the largest pilot cost, at 43% of the pilot pack; at 500 kg, ingredients and packaging make up 70% of the pack cost. The pilot pack price is therefore not a guide to the commercial price, and founders should model both.

Stacked bar chart of cost per 100 g dog treat pack: ₹103.9 at the 50 kg pilot (ingredients 11.9, run fee 35.0, testing 45.0, packaging 12.0) against ₹34.4 at a 500 kg run
Figure 1. Cost per 100 g pack at the 50 kg pilot and at a 500 kg run (calculated from assumed inputs; illustrative, not project results). Source: FRL.

What the dog treat pilot batch shows

On these assumptions the pilot costs ₹41,550, against ₹1,37,500 for a 500 kg run that would be lost if the recipe, process or pack failed at scale: the pilot buys the evidence for about 30% of the cost of a failed first run.

Finished moisture matters far less to cost than to safety (Table 3). Moving finished moisture from 8% to 12% changes the pilot cost per pack by about 4% (about 2% either side of the 10% target), because the solids, and so the number of packs, barely change.

Table 3. Effect of finished moisture on the 50 kg pilot (calculated; whole packs)

Finished moisture Treats (kg) Packs of 100 g ₹ per pack
8% 39.1 391 106.0
10% (target) 40.0 400 103.9
12% 40.9 409 101.9

Formulator’s note: set moisture and water-activity targets from shelf-life and safety data, not from yield. Drying to 12% instead of 10% adds about 2% more packs, which is worth far less than a mouldy or recalled batch.

Takeaways for your own project

  • Run a pilot before committing to an MOQ. It costs a fraction of a failed commercial run.
  • Fix the targets first: finished moisture, water activity, texture and shelf life, set from data on your own recipe.
  • Buy testing once, on the final recipe and pack. Re-testing after a late recipe change doubles the largest pilot cost.
  • Price at the MOQ, not at the pilot. Use the cost curve when negotiating run size and fees with a co-manufacturer.
  • Treat it as a sequence: recipe, processing trial, shelf life and safety, then scale.

For brands & formulators

Food Research Lab, based in Chennai, India, supports pet food brands from concept to pilot through our pet food product development services: formulation, pilot trials and scale-up, shelf-life work, palatability and acceptance trials, and regulatory guidance. For treats specifically, our functional pet treats team works on biscuits, chews and jerky strips.

Our animal food product development team also supports cost analysis for new products and limited batches for sampling and market testing, and our small and pilot lot contract manufacturing for animal and pet products is set up for start-ups that need a first lot before a full run. Shelf-life, microbiology and nutrient testing are run or arranged through accredited partner laboratories, and palatability and acceptance trials with dogs are run or arranged through partner facilities. See also our services in India.

Contact us with your recipe, target pack and shelf life, and the run size your co-manufacturer quotes.

What to do now
  • ✓Write the targets down first: finished moisture, water activity, texture and shelf life.
  • ✓Get three quotes for a pilot run and for the co-manufacturer’s minimum order quantity.
  • ✓Cost both runs per pack before you set a retail price.
  • ✓Budget shelf-life and pathogen testing on the final recipe and pack.
  • ✓Talk to our pet food product development team about your pilot.
Your next step
Plan your dog treat pilot batch
1Send your recipe, target pack size, shelf-life goal and any co-manufacturer quotes.
2FRL sets moisture and water-activity targets, plans the bake trial, testing and cost per pack.
3Receive a pilot plan and cost model you can take to your co-manufacturer and investors.
Questions brands ask
Is this a real FRL client project?

No. It is a labelled worked example. Brand P is a hypothetical start-up, and the batch size, moisture levels, ingredient, run-fee, testing and packaging costs are assumptions. Yields and costs per pack are calculated from those assumptions. No dogs were fed and no samples were tested, so no measured result is shown.

What is a dog treat pilot batch?

A dog treat pilot batch is a small production run, often tens of kilograms, used to test a recipe, process and pack before full manufacture. It shows the real yield after baking, whether moisture and water-activity targets are met, how the treat holds up in storage and what each pack will cost.

Why run a pilot batch before a full production run?

A pilot exposes texture, moisture, shelf-life and safety problems while volumes are small. In this worked example, the 50 kg pilot costs ₹41,550, against ₹1,37,500 for a 500 kg run that would be lost if the recipe or process failed at scale (both calculated from assumed inputs).

How are baked dog treats made?

Ingredients are weighed, mixed into a dough, shaped or cut, then baked or dried to a target moisture and water activity, cooled and packed. The bake profile is chosen in trials for texture and dryness, then fixed and validated. Soft chews and wet treats need different routes, such as humectants or retort processing.

How do you test a new dog treat for shelf life?

Packed treats are stored at room temperature and at a raised temperature, then checked over time for moisture, water activity, texture, rancidity and microbiology. Accelerated storage supports a provisional date; real-time storage confirms it. Pathogen testing, including Salmonella, is part of the safety work before launch.

Does finished moisture change the cost of a dog treat?

Only slightly. In this example, drying to 8% instead of 12% moisture changes the pilot cost per pack by about 4%, because the solids barely change. Moisture and water activity matter far more for safety and shelf life, so targets should come from storage and safety data, not yield.

References
  1. Ryu, M.-O., Lee, K.-H., Ha, H.-M., Kim, H.-R., Ahn, W.-S., Kim, S.-H., & Seo, K.-W. (2025). Proximate analysis and profiles of amino acids, fatty acids, and minerals in insect-based foods for dogs. American Journal of Veterinary Research, 86(1). https://doi.org/10.2460/ajvr.24.08.0243 (cited for measured values differing from declared values in 7 of 18 dog foods)
  2. Association of American Feed Control Officials. (n.d.). Selecting the right pet food. Retrieved 17 November 2026, from https://www.aafco.org/consumers/selecting-the-right-pet-food (cited for treat labelling and the absence of a nutritional adequacy statement on treats)
  3. Jobe, M. T., & Downs, K. M. (2025). Systematic review and meta-analysis of quality claims associated with fresh pet food: Evaluating scientific evidence for additives, ingredient quality, and effects of processing in pet nutrition. Animals, 16(1), 41. https://doi.org/10.3390/ani16010041 (cited for evidence on additives, preservatives and human-grade claims)
  4. Dhakal, J., Cancio, L. P. M., Deliephan, A., Chaves, B. D., & Tubene, S. (2024). Salmonella presence and risk mitigation in pet foods: A growing challenge with implications for human health. Comprehensive Reviews in Food Science and Food Safety, 23(6), e70060. https://doi.org/10.1111/1541-4337.70060 (cited for Salmonella as a pet food risk to pets and people)
  5. Beuchat, L. R., Komitopoulou, E., Beckers, H., Betts, R. P., Bourdichon, F., Fanning, S., Joosten, H. M., & Ter Kuile, B. H. (2013). Low-water activity foods: Increased concern as vehicles of foodborne pathogens. Journal of Food Protection, 76(1), 150–172. https://doi.org/10.4315/0362-028X.JFP-12-211 (cited for pathogen survival in low-water-activity foods and contamination control)
Continue the series · Part 5 of 5

Starting a pet food brand in India

1
Pet food regulations in India

What is mandatory and what is voluntary for a new dog treat brand.
2
Nutrient losses in pet food processingMAIN GUIDE

Raw, cooked and extruded compared, with taurine as the example.
3
Is a raw food diet for dogs safe?

Pathogen and nutrition evidence, and how brands lower the risk.
4
Packaging for dry pet food

Barrier, pest resistance and recyclability for kibble and treats.
5
Dog treat pilot batch: a worked exampleYou are here

One treat from recipe to pilot lot, costing and scale-up.